Page 1 of 1

Question about "join radial" without further clearance

Posted: Mon Feb 03, 2020 2:47 pm
by mh81
I filed IFR out of KSNA and got (approximately) this clearance: "fly heading 220 radar vectors Seal Beach VOR Santa Monica VOR then as filed". After taking off, departure gave me "fly heading 280 join the Santa Monica 125 radial". All good so far. Fly west, intercept the radial, turn right, and fly to SMO.

My question is, without further instructions (let's assume the frequency was congested and I wasn't able to get clarification), what am I expected to do on reaching SMO? If I'd heard "resume own navigation", I'd have just continued happily on after Santa Monica. Without that "resume own navigation" instruction, though, what is ATC expecting that I will do? Is it assumed that I'll continue on the clearance I received before taking off?

In this case I was able to ask for clarification and get further instructions, but I'm curious what ATC's expectation for me would have been if I hadn't been able to reach them.

The audio is here: http://audio.pilotedge.net/2020/2/2020-2-3_10_17510.mp3 The "join radial" instructions are at about the 30 second mark. I get clarification at about 1:55.

Thanks,

Marc

Re: Question about "join radial" without further clearance

Posted: Mon Feb 03, 2020 9:39 pm
by Keith Smith
If the SMO R-125 wasn't part of the cleared route to begin with, then I would question the controller as to what to do next. However, since the SMO R-125 was part of your cleared route (flight, including the route, shown here: http://peaware.pilotedge.net/flight.cfm?id=378823), then it would be reasonable to assume that you would continue with the cleared route at that point (that would be at SMO).

The controller essentially gave you a shortcut, bypassing SMO and V23, as is common with that real world airspace. Technically, "resume own navigation" should've been included in the instruction as mention in your post, however, the lack of such an instruction doesn't really introduce any ambiguity as to how to proceed. The controller did not alter the clearance limit (ie you should not hold at SMO, or at some random point on the SMO R-125).

Re: Question about "join radial" without further clearance

Posted: Sun Feb 16, 2020 7:03 pm
by jx_
"Resume own navigation" phraseology is never required until after an aircraft is established on its own navigation for the first time on each flight. This translates to all departing aircraft being vectored off the ground. Since you were assigned heading 220 you were never established on own navigation and therefore should not expect hear "resume own nav".

Re: Question about "join radial" without further clearance

Posted: Sun Mar 01, 2020 10:13 am
by mh81
Well, I think I found my answer in AIM 5-3-8:

(a): "Whenever an aircraft is cleared to a fix other than the destination airport and delay is expected, it is the responsibility of ATC to issue complete holding instructions (unless the pattern is charted), an EFC time and best estimate of any additional en route/terminal delay."

(c): "If no holding pattern is charted and holding instructions have not been issued, the pilot should ask ATC for holding instructions prior to reaching the fix. This procedure will eliminate the possibility of an aircraft entering a holding pattern other than that desired by ATC. If unable to obtain holding instructions prior to reaching the fix (due to frequency congestion, stuck microphone, etc.), then enter a standard pattern on the course on which the aircraft approached the fix and request further clearance as soon as possible. In this event, the altitude/flight level of the aircraft at the clearance limit will be protected so that separation will be provided as required."

Link: http://www.faraim.org/faa/aim/book/page_329.html

My interpretation is that, since the last clearance I received from the controller was, "join the Santa Monica 125 radial", that was my clearance limit. I had a responsibility to ask for clarification, "If no holding pattern is charted and holding instructions have not been issued, the pilot should ask ATC for holding instructions prior to reaching the fix" but, if I'm not able to get clarification, I'm to hold at that clearance limit until I'm able to get further instructions.

Re: Question about "join radial" without further clearance

Posted: Sun Mar 01, 2020 2:47 pm
by Marcus Becker
A clearance limit will be a defined point, not an airway or radial.

Re: Question about "join radial" without further clearance

Posted: Tue Mar 17, 2020 8:11 pm
by Greg Pfeil
If that situation happened in real world, I would join the radial fly to SMO then continue on my route as filed, as that was in my initial clearance. Just my .02 worth.