Assigning the IDENT to the Yoke or another control
-
- Posts: 60
- Joined: Fri Aug 04, 2017 11:29 am
Assigning the IDENT to the Yoke or another control
I am using P3D v4 and I was wondering if there is a hot key on the PE program, kind of like push to talk. I know there is no assignment choice but I was wondering if there was a key stroke in the background that would work. Right now I need to get out of the sim, well switch, and set it in PE. I am using Saitek and CH products
Dean Salman
N117SB Diamond Twin Star
N117SB Diamond Twin Star
Re: Assigning the IDENT to the Yoke or another control
I have a yoke button on my Saitek yoke assigned to IDENT via registered FSUIPC. Works great.
Commercial / Instrument / KMLB
-
- Posts: 60
- Joined: Fri Aug 04, 2017 11:29 am
Re: Assigning the IDENT to the Yoke or another control
I have this setup Are you using XPNDR Set or XPNDR Ident (sb4) I am using the second one
I think it is working with a parameter set at 1
I think it is working with a parameter set at 1
Dean Salman
N117SB Diamond Twin Star
N117SB Diamond Twin Star
Re: Assigning the IDENT to the Yoke or another control
xpndr ident (sb4) Maybe it's ignoring the parameter. I have no parameter (0) and it's fine that way.
Commercial / Instrument / KMLB
-
- Posts: 503
- Joined: Mon Jan 24, 2011 11:41 am
- Location: KPDX
- Contact:
Re: Assigning the IDENT to the Yoke or another control
Moved to P3D forum.
-
- Posts: 60
- Joined: Fri Aug 04, 2017 11:29 am
Re: Assigning the IDENT to the Yoke or another control
So this just does nit want to work. I am considering getting flight illision transponder radio with has a ident key, so other software is not needed other than what comes with it. So hopefully this will work and PE will see when I press the ident
Dean Salman
N117SB Diamond Twin Star
N117SB Diamond Twin Star
Re: Assigning the IDENT to the Yoke or another control
Not sure what else I can do to help here... works great for me. Here is the line in FSUIPC5.ini that I have in the profile specific BUTTONS section. I just did it that way but you can make it in the general assignments also. This doesn't do anything in the cockpit, it simply sends the IDENT to PE (button #2 below). No lights, no knobs, no buttons move in the cockpit, it's not a gauge. Others have successfully modified some specific aircraft panels to integrate the Mode C and in fewer cases the IDENT function. MervA has done some great work on this viewtopic.php?f=8&t=6372.
[Buttons.Phenom]
0=PB,0,C1001,0 ; #1 -{PTT Transmit On (SB3,RW,AVC)}-
1=UB,0,C1002,0 ; #1 -{PTT Transmit Off (SB3,RW,AVC)}-
2=PB,1,C1122,0 ; #2 -{xpndr ident (sb4)}-
[Buttons.Phenom]
0=PB,0,C1001,0 ; #1 -{PTT Transmit On (SB3,RW,AVC)}-
1=UB,0,C1002,0 ; #1 -{PTT Transmit Off (SB3,RW,AVC)}-
2=PB,1,C1122,0 ; #2 -{xpndr ident (sb4)}-
Commercial / Instrument / KMLB