Reporting midfield when its busy

Reporting midfield when its busy

Postby tbaac » Sun Aug 26, 2018 1:12 pm

Hi
Came back to PE again after having a membership for a while previously but not really flying. This time I'm having much more fun, thanks.

I wondered about pattern work when the radio is busy.
If I'm due to report midfield and there is a conversation on the radio at the time, what is the best thing to do?
Should I continue on downwind until I get landing/option clearance?

Also, my transponder switch has positions for Off, Standby, On and Alt.
I think it should be set to Alt when on the runway and in the air.
Which setting to use whilst taxiing? On or just Standby?

Thanks.
tbaac
 
Posts: 38
Joined: Sat May 14, 2016 2:32 pm
Location: EGLF, England

Re: Reporting midfield when its busy

Postby zerofay32 » Mon Aug 27, 2018 5:37 am

For pattern work, continue the traffic pattern until you can get a word in and just report your actual position (i.g. "N123AB abeam the numbers, touch and go" or "N123AB turning final, full stop") Also it may help to extend your downwind slightly but no need to make it excessive. If by some chance of bad luck you still cant get a call in, don't land but just go around for another circuit and inform the tower when you get a chance.

The AIM has recommended that pilots have the transponder in ALT at all times for several years now. This also makes it easy because you then don't have to remember which airports have ground surveillance systems that require it to be in this mode.
Andrew Fay
PilotEdge I-11
Commercial Pilot/Instrument ASEL- KOSU / Commercial sUAS-DJI S900
PE Callsigns: C172-62266; PA28-6157J; DHC6-2612J; PA31-35834
ZLA Alphabet Challenge http://myflightroute.com/alpharesults.php?pilot=%284171%29
zerofay32
 
Posts: 96
Joined: Tue Aug 19, 2014 8:34 am
Location: Grove City, Ohio

Re: Reporting midfield when its busy

Postby tbaac » Mon Aug 27, 2018 11:11 am

Thanks for the reply zerofay32.

I did the CAT3 yesterday and on the 3rd lap I was due to report midfield and as it was busy I had turned onto base by the time I'd reported in to the controller.
I suppose that you don't need clearance to turn onto base, so as it happened it wasn't the end of the world, but I thought about it afterwards and realised if I'd not been able to get clearance whilst on base then I might have had nowhere to go.

Thanks for that about the transponders, good to know.
tbaac
 
Posts: 38
Joined: Sat May 14, 2016 2:32 pm
Location: EGLF, England

Re: Reporting midfield when its busy

Postby jx_ » Mon Aug 27, 2018 5:58 pm

the pattern instruction you received permits you to turn base. It is the controller's responsibility to amend the instructions if there is a conflict. However, if you alter or extend your pattern at all, you take responsibility. ;)
jx_
 
Posts: 443
Joined: Wed Jan 22, 2014 12:15 am

Re: Reporting midfield when its busy

Postby Shawn Goldsworthy » Mon Aug 27, 2018 6:01 pm

Just to add to what Joe said (which is 100% accurate) if you still can't get a word in, go around.
Shawn Goldsworthy
PilotEdge ATCS
Image
Shawn Goldsworthy
 
Posts: 417
Joined: Sun Nov 07, 2010 9:23 pm
Location: Nova Scotia, Canada


Return to General

Who is online

Users browsing this forum: No registered users and 4 guests